181,957 users have contributed to 42,195 threads and 254,637 posts.
In the past 24 hours, we have 4 new thread(s), 12 new post(s) and 54 new user(s).
the difference between DDR 266 (aka PC2100) and DDR333 (aka PC2700) would hardly be noticable, but DDR667 (aka PC2-5300) is another type of RAM (1.8 vs. 2.5 V) and runs mostly as dual channel memory needing another controller, means another motherboard ... and is of course much faster ...
you would notice a huge difference for loading time (if your harddisks can deliver data ...)
christian
@cm said:
you would notice a huge difference for loading time (if your harddisks can deliver data ...)
Really? Actually I was wondering about this as well with the dreaded RAM timing question... 5-5-5-18 vs. 4-4-4-12 e.g. Does it really make a noticeable difference? I doubt that because memory bandwidth is already several GB/s with PC2100 and of course a lot higher with PC2-5300 or PC2-6400. With harddrives delivering a few 100MB/s at max even when RAIDed it does not really matter I think.
And as far as reading sample buffers from it goes, there's the fixed 64kb buffer, that will get delivered quickly enough no matter how fast the RAM is, and won't change a thing regarding possible polyphony. Or didn't I think of something more or less obvious?
PolarBear
@Simsy said:
Thanks cm. Would a PC with 2 Dual Xeon 2.4 CPU's in it and 16GB of DDR333 RAM be fast enough to run vienna on?
Simsy, which board do you have in mind? Dunno for sure, but I think there are not many boards for Dual Xeon that support DDR333 RAM if there is any... did you check back with the specifications of the manufacturor if that's a possibility? Did you also look if it doesn't need fully buffered DDR2 DIMMs? I'm pretty sure it does.
PolarBear
IIRC bandwidth for PC2100 is at best 2.1 giga_bit/sec which is a burst rate and equals to 260 MB/s without considering any wait-states, refresh-cycles ect ...
however there are XEON 2,4 GHz with a 533 FSB and DDR266 dual channel .... could be a good buy currently (you can get them as refurbished machines ffor ~ 400 EUR with at least some RAM)
christian
No problem PolarBear, I appreciate all the advice that I get. I just want to make sure that this spec of a machine is going to work with VE.@PolarBear said:
Btw. I'm sorry Simsy that my answers to your threads have not been very helpful or even possibly misleading to you. Just thought I could help there!
All the best,
PolarBear
I am sorry to ask again, but will it run a few say, 4 or 5 Vienna Ensembles fine? But it will just take a while to load all the samples into memory? Or is the memory speed going to reduce the number of Vienna Instruments that I can run?@cm said:
basically yes, try to get as much RAM as possible (of course more than 4 GB needs a 64bit OS)
christian
no problem - just ask, not everybody is a computer technician ...
slow components will slow down all processes
- slower RAM will slow down the loading process
- a slow harddisk might limit you in the amount of voices which can be streamed simultaneously
- a slow processor (something about 1 GHz) would limit you anyway ...
- a Vienna Ensemble Instance needs about 50 MB RAM
- each inserted ViennaInstrument will need about 20 MB RAM
- each loaded preset/matrix/patch will need the respective memory
so depending on the available memory of your computer you can run a certain number of VEs with more or less inserted VIs loading the selected content
CPU wise a dual XEON 2.4 should give you at least 30 simultaneously loaded and playing tracks ....
christian
say if 50 ViennaInstruments need 20% CPU on a 2 core2duo 2.8 then consider they will need ~ 25% CPU on a 2 x core2duo 2.0
i can't remember exactly but a very early test on a quad XEON woodcrest 2.8 (2 x dual core XEON) with 48 ViennaInstruments needed 17% CPU (this figure might vary a little bit depending on what you've loaded)
every intel processor better than and including coreDuo can run 64bit operating systems (i'd assume you actually can no longer purchase any which can not)
christian
